Thermite

[COBHC#666]

Thermite is nasty shit. Here is a good and easy way to make it.
The first step is to get some iron-oxide (which is RUST!). Here is
a good way to make large quantities in a short time:
- Get a DC convertor like the one used on a train set. Cut the
connector off, seperate the wires, and strip them both.
- Now you need a jar of water with a tablespoon or so of sodium
chloride (which is SALT!) added to it. This makes the water
conductive.
- Now insert both wires into the mixture (I am assuming you
plugged the convertor in...) and let them sit for five minutes.
One of them will start bubbling more than the other. This is the
POSITIVE(+) wire. If you do not do this test right, the final
product will be the opposite (chemically) of rust, which is RUST
ACID. You have no use for this here (although it IS useful!).
- Anyway, put the nail tied to the positive wire into the jar. Now
put the negative wire in the other end. Now let it sit overnight
and in the morning scrape the rust off of the nail & repeat until
you got a bunch of rust on the bottom of the glass. Be generous
with your rust collection. If you are going through the trouble of
making thermite, you might as well make a lot, right?
- Now remove the excess water and pour the crusty solution onto a
cookie sheet. Dry it in the sun for a few hours, or inside
overnight. It should be an orange-brown color (although I have
seen it in many different colors! Sometimes the color gets fucked
up, what can I say... but it is still iron oxide!)
- Crush the rust into a fine powder and heat it in a cast-iron pot
until it is red. Now mix the pure iron oxide with pure alluminum
filinos which can be bought or filed down by hand from an aluminum
tube or bar. The ratio or iron oxide to aluminum is 8 grams to 3
grams.
- Congrats! You have just made THERMITE! Now, to light it...
- Thermite requires a LOT of heat (more than a blow torch!) to
ignite. However, a magnesium ribbon (which is sorta hard to find..
call around) will do the trick. It takes the heat from the
burning magnesium to light the thermite.
- Now when you see your victim's car, pour a fifty-cent sized pile
onto his hood, stick the ribbon in it, and light the ribbon with
the blow torch. Now chuckle as you watch it burn through the hood,
the block, the axle, and the pavement. BE CAREFUL! The ideal
mixtures can vaporize CARBON STEEL! Another idea is to use
thermite to get into pay phone cash boxes. HAVE FUN!!


Is this not the shit or what?

[[ g h o s t ]]

No, it is not.

What you have produced is shitty, poorly-mixed, contaiminated, barely reacting thermite. In fact, that veyr procedure is pure copypaste.

Thermite will not melt through the engine block, the axle and the pavement. if you're lucky, it will make the hood hot enough so the little spot collapses and they get some molten iron on their engine.

It can't vaporise carbon steel, it's only even hot enough to melt pure pig iron.

Thermite can be ignited with a blowtorch - Provided it is the right kind of blowtorch.



I got bored of thermite after I ignited a 44-gallon drum full of the shit.

[BlackZodiac]

Now here's a pretty cool video of thermite.

http://www.youtube.com/watch?v=FEmHJORTlqk

[faggypunk]

No, it is not.

What you have produced is shitty, poorly-mixed, contaiminated, barely reacting thermite. In fact, that veyr procedure is pure copypaste.

Thermite will not melt through the engine block, the axle and the pavement. if you're lucky, it will make the hood hot enough so the little spot collapses and they get some molten iron on their engine.

It can't vaporise carbon steel, it's only even hot enough to melt pure pig iron.

Thermite can be ignited with a blowtorch - Provided it is the right kind of blowtorch.



I got bored of thermite after I ignited a 44-gallon drum full of the shit.

yea he's kinda right
but if you look on ebay, you cant buy it mixed together and ready to burn
although they sell really good quality ingrediants

[[ g h o s t ]]

Now here's a pretty cool video of thermite.

http://www.youtube.com/watch?v=FEmHJORTlqk

Just so you know, the first part is fake. Notice how you don't get to see any shots of the 'eaten-through' engine block, only the .5mm mild steel sheet hood?


Even so, they use a lot more then the 'fifty-cent sized pile'.

[COBHC#666]

man i no its copy and paste theres just been so many questions from dumbass people i thought i would let them try and fail at this one

[faggypunk]

so how much thermite would it take to melt through the engine block?

[TerryWrist69]

yo fuck stick, don't just copy and paste shit from the anarchist cook book, weve all fucking read it, we don't need little bitches like you to remind us just how infective that method is.

[suffertheconsequences]

yo fuck stick im glad your here cuz we need little bitches like you to bend over and take it in the ass

[[ g h o s t ]]

so how much thermite would it take to melt through the engine block?

Probably about five kilos. Less if it's something like an old-model VW beetle (they have a magnesium alloy block, hahah)