Ok i just got an urgent request for silencers, anyone have plans for these?
Automatic 9mm 1911 Colt
Automatic .45 1911 Colt

google turned up nothing?

Alot of books on amazon for exactly what I need.
No free sites, kinda strange.

just go to this link http://thepiratebay.org/torrent/3960...ook_Collection and download the torrent. you need a program like utorrent to download it. you can get the program at utorrent.com.

if you dont know how suppressers work read this if u do them go down
suppressers are a tube with alot of gas chamber in them to capture gas an still let the bullet out
so i resently made one for my bolt action .22 i took a peice of PVC pipe and cut out some cardbord and stacked it up in the PVC pipe and put a bootle cap on the end to keep the cardboard in and taped it off then i put the end not taped off on the gun barrel so it works okay but you CANT used ammo that goes over 1250 fps i think becuase the bullet breaks the sound barrior causing a crack downrange that canot be avoided so use ammo that dosent break the sound barrior

I love how all the guns in the second video are just fucking sitting there xD

I've been looking at these plans for the past few days and i find this site just now, and i already found someone who can use it. hope it's what u needed


Low signature systems (silencers) for improvised small arms weapons can be made from steel gas or water pipe and fittings.

Material Required:
Grenade Container
Steel pipe nipple, 6 in. (15 cm) long - (see table 1 for diameter)
2 steel pipe couplings - (see table 2 for dimensions)
Cotton cloth - (see table 2)
Drill
Absorbent cotton

Procedure:
Drill hole in grenade container at both ends to fit outside diameter of pipe nipple. (see table 1)

-> /----------------------\
/ | |
2.75 in | ) ( <-holes
dia. \ | |
-> \-----------------------/

|-----------------------|
5 in.

Drill four rows of holes in pipe nipple. Use table 1 for diameter and location of holes.
(Note: I suck at ASCII art!)

6 in.
|-----------------------------------|
_____________________________________ ___
| O O O O O O O O O O O O O O O O O | | C (nom. dia.)
-------------------------------------
(size of hole) | \ / (space between)
B (dia.) A

Thread one of the pipe couplings on the drilled pipe nipple.
Cut coupling length to allow barrel of weapon to thread fully into low signature system. Barrel should butt against end of the drilled pipe nipple.
Separate the top half of the grenade container from the bottom half.
Insert the pipe nipple in the drilled hole at the base of the bottom half of the container. Pack the absorbent cotton inside the container and around the pipe nipple.
Pack the absorbent cotton in top half of grenade container leaving hole in center. Assemble container to the bottom half.
Thread the other coupling onto the pipe nipple.

Note: A longer container and pipe nipple, with same "A" and "B" dimensions as those given, will further reduce the signature of the system.

How to use:

Thread the low signature system on the selected weapon securely.
Place the proper cotton wad size into the muzzle end of the system (see table 2)
Load weapon
Weapon is now ready for use

TABLE 1
Low Signature System Dimensions

Coupling Holes per 4 rows
A B C D Row Total
.45 cal 3/8in ¼in 3/8in 3/8in 12 48
.38 cal 3/8in ¼in ¼in ¼in 12 48
9 mm 3/8in ¼in ¼in ¼in 12 48
7.62 mm 3/8in ¼in ¼in ¼in 12 48
.22 cal ¼in 5/32in 1/8*in 1/8in 14 50
* Extra Heavy Pipe


TABLE 2
Cotton Wadding Sizes

Weapon Cotton Wadding Size
.45 cal 1-½ x 6 inches
.38 cal 1 x 4 inches
9 mm 1 x 4 inches
7.62 mm 1 x 4 inches
.22 cal Not needed